Pines Delivers New Bender for Spanish Air Force
Pines has delivered a new Pines #2 NC bender to the Spanish Air Force. With the capability to make multiple bend parts up to 3-inch in diameter this m...
Model 3T
The Model 3T Vertical Compression Bender is self-contained with a hydraulic oil reservoir incorporated in the base and equipped with a water-cooled heat exchanger, 20 HP electric motor, hydraulic pump, and all necessary valves.
Steel Tube Capacity: 1.25” OD x .065 WT
1 tube at a time
Series 44361
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 1.25” x .065
- Round tubing, non-ferrous Y.P. to 25,000 psi – 1.25” x .083
- Round tubing, stainless steel Y.P. to 60,000 psi – 1.25” x .049
- Square tubing, mild steel – 1” x .065
- Round bar, mild steel – ¾”
- Square bar, mild steel – 9/16”
- Maximum section modulus, mild steel – .072
- 1 tube at a time
- Production capacity, bends per hour approximate – 1,000 strokes (bends)
- Maximum standard radius for 90° bend – 4.5”
- Minimum radius to diameter ratio – 2 to 3
- Maximum bend angle – 140º
- Maximum bend angle with special tooling – 165°
- Bend arm repeatability – ± ¼°
- Motor horsepower – 20HP
- Approximate weight – 4,600 lbs.
- Overall height – 60 inches
- Working height to dies – 40 inches
- Footprint (floor space required) – 30 x 80 inches
- Weight – 2,900 lbs
- All electrical components in power panel are “finger-safe” and are in accordance with NFPA standards
- Machine is labeled with pinch and hazard points
Model 5T
The Model 5T expands on the Model 3T, including an outboard wing die cushion assembly, wing die holder extensions, and necessary piping to permit bending two tubes at once vs. the Model 3T’s one tube at a time.
1.25” OD x .065 WT - 1 tube at a time
1.00” OD x .065 WT – 2 tubes at a time
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 1.25” x .065 (1.0” x .072 – two at a time)
- Round tubing, non-ferrous Y.P. to 25,000 psi – 1.25” x .083 (1.0” x .065 – two at a time)
- Round tubing, stainless steel Y.P. to 60,000 psi – 1.25” x .049 (1.0” x .049 – two at a time)
- Square tubing, mild steel – 1” x .065 (7/8” x .035 – two at a time)
- Round bar, mild steel – ¾” (5/8” two at a time)
- Square bar, mild steel – 9/16” (1/2” two at a time)
- Maximum section modulus, mild steel – .072 (.036 two at a time)
- 1 or 2 tube at a time
- Production capacity, bends per hour approximate – 650 strokes (bends)
- Production capacity, bends per hour approximate – two at a time – 1,300
- Maximum standard radius for 90° bend – 4.5”
- Minimum radius to diameter ratio – 2 to 3
- Maximum bend angle – 140º
- Maximum bend angle – two at a time – 100°
- Maximum bend angle with special tooling – 165°
- Bend arm repeatability – ± ¼°
- Motor horsepower – 20HP
- Approximate weight – 4,600 lbs.
- Overall height – 60 inches
- Working height to dies – 40 inches
- Footprint (floor space required) – 30 x 85 inches
- Weight – 3,100 lbs
- All electrical components in power panel are “finger-safe” and are in accordance with NFPA standards
- Machine is labeled with pinch and hazard points