Pines Delivers New Bender for Spanish Air Force
Pines has delivered a new Pines #2 NC bender to the Spanish Air Force. With the capability to make multiple bend parts up to 3-inch in diameter this m...
CNC 040
Pines CNC 040 Bending Machine, with capacity for 1 1/2” x .109” steel tubing, is arranged for counterclockwise rotation with 8-inch maximum radius. It comes complete with carriage for positioning of tubes with multiple bend configurations, hydraulic mandrel extractor, heavy-duty mandrel lubricator, clamp and pressure die holders, automatic slide lubricator, all necessary hydraulics, valves, piping, and cylinders. Complete bender operations are self contained in the machine base and include water-cooled heat exchanger for the hydraulic oil.
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 1 1/2” x .109”
- Round tubing, non-ferrous Y.P. to 25,000 psi – 1 5/8” x .135”
- Round tubing, stainless steel Y.P. to 60,000 psi – 1 3/8” x .065
- Steel pipe, schedule 80 – 1
- Square tubing, mild steel – 1 1/8“x .120
- Maximum standard radius – 8”
- Minimum radius to diameter ratio – 1
- Maximum bend angle – 190º
- Centerline height – 1.625”
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .005”
- Standard tube length over mandrel – 10’
- Bend arm forward speed –21 RPM
- Bend arm reverse speed – 39 RPM
- B-axis travel: 360º – Speed: 60 RPM
- Y-axis travel: 6’ – Speed: 2400 IPM
- Motor horsepower – 15HP
- Dimensions – ~ 15’ L x 4’ W x 4’ H
- Working height ~ 37.5”
- Voltage – 480 3 phase 60 Hz. 40 amp circuit required (220/3/60 @ 80 amps also available)
- Weight – Approximately 4,500 lbs.
- Oil reservoir – Completely sealed reservoir with 40-gallon capacity
CNC 075
Pines CNC 075 Bending Machine, with capacity for 3” x .109” steel tubing, is arranged for counterclockwise rotation with 12-inch maximum radius. The machine comes complete with electric servo carriage for positioning of tubes with multiple bend configurations, hydraulic mandrel extractor, heavy-duty mandrel lubricator, clamp and pressure die holders, automatic slide lubricator, all necessary hydraulics, valves, piping, and cylinders. Complete bender operations are self-contained in the machine base and include water-cooled heat exchanger for the hydraulic oil.
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 3” x .109
- Round tubing, non-ferrous Y.P. to 25,000 psi – 3” x .187
- Round tubing, stainless steel Y.P. to 60,000 psi – 3” x .065
- Steel pipe, 2 IPS schedule 80
- Square tubing, mild steel – 2” x .125
- Maximum standard radius – 12”
- Minimum radius to diameter ratio – 1
- Maximum bend angle – 190º
- Centerline height – 2.0”
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .005”
- Standard tube length over mandrel – 12’
- Average bend arm speed – 14 RPM
- B-axis travel: 360º – Speed: 45 RPM
- Y-axis travel: 6’ – Speed: 2400 IPM
- Motor horsepower – 20HP
- Dimensions – ~ 16’ L x 5’ W x 5’ H
- Working height ~ 40”
- Voltage – 480 3 phase 60 Hz. 45 amp circuit required (220/3/60 @ 75 amps also available)
- Weight – Approximately 8500 lbs.
- Oil reservoir – Completely sealed reservoir with 55-gallon capacity
CNC 100
Pines CNC 100 Bending Machine, with capacity for 4” x .065” stainless steel tubing, is arranged for counterclockwise rotation with 12-inch maximum radius. The machine comes complete with carriage for positioning of tubes with multiple bend configurations, hydraulic mandrel extractor, heavy-duty mandrel lubricator, clamp and pressure die holders, automatic slide lubricator, all necessary hydraulics, valves, piping, and cylinders. Complete bender operations are self-contained in the machine base and include fan-cooled heat exchanger for the hydraulic oil.
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 4” x .109
- Round tubing, non-ferrous Y.P. to 25,000 psi – 4” x .188
- Round tubing, stainless steel Y.P. to 60,000 psi – 4” x .065
- Steel pipe, 2.5 IPS schedule 80
- Square tubing, mild steel – 2” x .125
- Maximum standard radius – 12”
- Minimum radius to diameter ratio – 1
- Centerline height – 2.5”
- Maximum bend angle – 195º
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .005”
- Standard tube length over mandrel – 136”
- Bend arm speed – 21 RPM
- B-axis travel: 360º – Speed: 30 RPM
- Y-axis travel: 6’ – Speed: 2400 IPM
- Motor horsepower – 40HP
- Dimensions – ~ 18.8’ L x 6’ W x 5’ H
- Working height ~ 42”
- Voltage – 480 3 phase 60 Hz. 45 amp circuit required (220/3/60 @ 75 amps also available)
- Weight – Approximately 4500 lbs
- Oil reservoir – Completely sealed reservoir with 100-gallon capacity
CNC 150
Pines CNC 150 Bending Machine, with capacity for 6” x .165” steel tubing, is arranged for counterclockwise rotation with 18-inch maximum centerline radius. The machine comes complete with carriage for positioning of tubes with multiple bend configurations, hydraulic mandrel extractor, heavy-duty mandrel lubricator, clamp and pressure die holders, twin overhead tie bars, automatic slide lubricator, all necessary hydraulics, valving, piping, and cylinders. Complete bender operations are self-contained in the machine base and include water-cooled heat exchanger for the hydraulic oil.
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 6” x .165
- Round tubing, non-ferrous Y.P. to 25,000 psi – 6” x .250
- Round tubing, stainless steel Y.P. to 60,000 psi – 6” x .065
- Steel pipe, 4 IPS schedule 80
- Square tubing, mild steel – 4” x .250
- Maximum standard radius – 18”
- Minimum radius to diameter ratio – 1
- Centerline height – 3.75”
- Maximum bend angle – 195º
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .010”
- Standard tube length over mandrel – 14’
- Bend arm speed – 3.4 RPM Average
- B-axis travel: 360º – Speed: 15 RPM
- Y-axis travel: 9’ – Speed: 1200 IPM
- Motor horsepower – 30HP
- Dimensions – ~ 30’ L x 10’ W x 5’ H
- Working height ~ 51”
- Voltage – 480 3 phase 60 Hz. 45 amp circuit required (220/3/60 @ 75 amps also available)
- Weight – Approximately 14,500 lbs
- Oil reservoir – Completely sealed reservoir with 150-gallon capacity
CNC 200
Pines CNC 200 Bending Machine, with capacity for 6” Sch 160 pipe, is arranged for clockwise rotation with 30-inch maximum radius. The machine comes complete with carriage for positioning of tubes with multiple bend configurations, hydraulic mandrel extractor, heavy-duty mandrel lubricator, clamp and pressure die holders, all necessary hydraulics, valves, piping, and cylinders. Complete bender operations are self-contained in the machine base and include fan-cooled heat exchanger for the hydraulic oil.
Technical Data
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 8” OD x .250 wall
- Round tubing, non-ferrous Y.P. to 25,000 psi – 8” OD x .375 wall
- Round tubing, stainless steel Y.P. to 60,000 psi – 8” OD x .172 wall
- Steel pipe, schedule 160 – 6” NPS
- Square tubing, mild steel – 4.5” square x 1.0” wall
- Through collet carriage – 6.625” OD and 4.5” SQ
- End chuck carriage – 8” OD and 5.5” SQ
- Maximum standard radius – 30”
- Minimum radius to diameter ratio – 1
- Centerline height – 6.0”
- Maximum bend angle – 195º
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .020”
- Standard tube length over mandrel – 240”
- Bend arm speed – 0.7 RPM Average
- B-axis travel: 360º
- Y-axis travel: 15’
- Motor horsepower – 30HP
- Dimensions – ~ 32’ L x 10.5’ W x 7.25’ H
- Working height ~ 50”
- Voltage – 480V 3 phase 60 Hz. 45 amp circuit required (other voltages available)
- Weight – Approximately 44,500 lbs
CNC 010
Electric Tabletop Bender with Pneumatic Tool Action
The CNC 10 is a fully automatic bench-top coaxial cable bender that produces complex parts quickly and efficiently. This electric bender with pneumatic tool action requires minimal operator assistance. Cable is simply loaded through the carriage while all three axes movements of the bending sequence are executed automatically to complete the part.
Technical Data
Configuration
Many options are available to customize the machine. Including but not limited to:
Features
Capacities
Specifications
Safety Features
- The Pines CNC 010 is built to stock with the following standard equipment:
- Clockwise & counterclockwise rotation capability
- Hitch feed function
- Unlimited part length
- Integrated tool storage
- Fully automatic, semi-automatic, and manual modes
- Color touch screen
- Spring back compensation
- Program up to 32 bends per part
- Each axis has 10 independent speed settings
- Roller die holder
- Clamp die holder
- Servo controlled swing arm
- Ethernet port for PC communications
Many options are available to customize the machine. Including but not limited to:
- Capability to bend .25” OD aluminum and copper coaxial cable with Heavy Duty head
- Manual cut off saw
- Drop away swing arm roller option
- Power converter for alternate voltages
Features
- Hitch feed
- Open collet bending
- Automatic, semi-automatic and manual mode
- Includes TS workstation PC compatible
- software package
- Part program entry from XYZ, or YBC data
- Part program data conversion to or from XYZ or YBC
- Part program data conversion to or from absolute or incremental
- Part program storage on hard disk or USB memory stick
- Part program reversal and mirror image conversions
- Graphic display of the part with ability to rotate in any direction.
- Dimensions – ~ 30’ L x 10’ W x 5’ H
Capacities
- .141 OD semi rigid coaxial cable
- .250 OD semi rigid coaxial cable with optional interchangeable heavy-duty head
Specifications
- Maximum standard radius – 1.125”
- Minimum radius to diameter ratio – 1.5D (1D possible but bend quality may suffer)
- Maximum bend angle – 195º
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .005”
- B-Axis travel: 360º
- Y-Axis travel: 24”
- Tabletop installation
- Electrical – 120 Volt, 1 Phase, 60 Hz, 10 amps
- Pneumatic: 70-90 PSI
- Weight – Approximately 150 lbs
- Dimensions – ~ 50” L x 28” W x 18”
Safety Features
- All electrical components in power panel are “finger-safe” and are in accordance with NFPA standards
CNC 015
Electric Tabletop Bender with Pneumatic Tool Action
The CNC-15 is a fully automatic bench-top bender that can produce a wide variety of complex parts quickly and efficiently. This electric bender with pneumatic tool action requires minimal operator assistance. Material is simply loaded through the carriage while all three axes movements of the bending sequence are executed automatically to complete the part.
Technical Data
Configuration
Options are available to customize the machine. Including but not limited:
Machine Features
Capacities
Specifications
Safety Features
- The Pines CNC 015 is built with the following standard equipment:
- Counterclockwise rotation
- 1xD bend capability
- Hitch feed function
- Integrated tool storage
- Fully automatic, semi-automatic, and manual modes
- Color touch screen
- Spring back compensation
- Program up to 32 bends per part
- Each axis has 10 independent speed settings
- Pressure die holder
- Clamp die holder
- Mandrel extractor
- Safety mat
- Servo controlled swing arm
- Ethernet port for PC communications
Options are available to customize the machine. Including but not limited:
- Clockwise rotation
- UL Version
- Laser Safety Scanner
- Power converter for alternate voltages
- CMM interface capability
Machine Features
- Hitch feed
- PDI zone recapture
- Springback compensation
- Open collet bending
- Automatic, semi-automatic and manual mode
- Includes TS Workstation PC compatible software package
- Part program entry from XYZ, or YBC data
- Part program data conversion to or from XYZ or YBC
- Part program data conversion to or from absolute or incremental
- Part program storage on hard disk or USB memory stick
- Part program reversal and mirror image conversions
- Graphic display of the part with ability to rotate in any direction
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 1/2” x .049” wall
- Round tubing, non-ferrous Y.P. to 25,000 psi – 5/8” x .042” wall
- Round tubing, stainless steel Y.P. to 60,000 psi – 3/8” x .065” wall
- Solid wire, mild steel – 5/16”
Specifications
- Maximum standard radius – 3.0”
- Minimum radius to diameter ratio – 1
- Maximum bend angle – 195º
- Bend arm repeatability – +/- .1º
- Carriage repeatability – +/- .005”
- Standard tube length over mandrel – 72”
- B-axis travel: 360º
- Y-axis travel: 36”
- Dimensions ~ 86” L x 21”W x 28” H
- Working height ~ tabletop
- Voltage – 120 Volt, 1 Phase, 60 Hz.
- Pneumatics – 70 – 90 PSI
- Weight – Approximately 400 lbs
Safety Features
- Safety plates protecting both bend and return sides of swing arm
- All electrical components in power panel are “finger-safe” and are in accordance with NFPA standards
- Machine is labeled with pinch and hazard points