440.278.7200Machines
Vertical Compression NC Tube Benders
Pines vertical compression benders are unmatched in speed and versatility. Simple to use and simple to maintain these machines are pound for pound the most productive in the industry. With production rates of 1000-1500 bends per hour they pay for themselves in no time and will continue to make parts for decades to come.
Model 3T
Configuration
The Pines Model 3T is built to stock with the following standard equipment:
- Series 44361
- Variable speed ram
- Hydraulically cushioned wing die holders
- Variable wing die pressure control
- Die holders
- Water cooled heat exchanger
- 2 to 3 x D bend capability
- 7 Inch color touch screen Dial-A-Bend® DAB 7 Control
Options are available to customize the machine. Including but not limited to:
- Set of stops and gauges for locating bends in various planes
- Dual palm remote stand
- Plug adaptor (allows control to be unplugged from Disconnect box)
- Fan cooled heat exchanger
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 1.25” x .065
- Round tubing, non-ferrous Y.P. to 25,000 psi – 1.25” x .083
- Round tubing, stainless steel Y.P. to 60,000 psi – 1.25” x .049
- Square tubing, mild steel – 1” x .065
- Round bar, mild steel – ¾”
- Square bar, mild steel – 9/16”
- Maximum section modulus, mild steel – .072
- 1 tube at a time
- Production capacity, bends per hour approximate – 1,000 strokes (bends)
Specifications
- Maximum standard radius for 90° bend – 4.5”
- Minimum radius to diameter ratio – 2 to 3
- Maximum bend angle – 140º
- Maximum bend angel with special tooling – 165°
- Bend arm repeatability – ± ¼°
- Motor horsepower – 20HP
- Approximate weight – 4,600 lbs.
- Overall height – 60 inches
- Working height to dies – 40 inches
- Footprint (floor space required) – 30 x 80 inches
- Weight – 2,900 lbs
Safety Features
- All electrical components in power panel are “finger-safe” and are in accordance with NFPA standards
- Machine is labeled with pinch and hazard points
Model 5T
Configuration
The Pines Model 5T is built to stock with the following standard equipment:
- Series 44362
- Variable speed ram
- Hydraulically cushioned wing die holders
- Variable wing die pressure control
- Die holders
- Bend one or two tubes at a time per stroke
- Water cooled heat exchanger
- 2 to 3 x D bend capability
- 7 Inch color touch screen Dial-A-Bend® DAB 7 Control
Options are available to customize the machine. Including but not limited to:
- Set of stops and gauges for locating bends in various planes
- Dual palm remote stand
- Plug adaptor (allows control to be unplugged from disconnect box)
- Fan cooled heat exchanger
Capacities
- Round tubing, mild steel Y.P. to 40,000 psi – 1.25” x .065 (1.0” x .072 – two at a time)
- Round tubing, non-ferrous Y.P. to 25,000 psi – 1.25” x .083 (1.0” x .065 – two at a time)
- Round tubing, stainless steel Y.P. to 60,000 psi – 1.25” x .049 (1.0” x .049 – two at a time)
- Square tubing, mild steel – 1” x .065 (7/8” x .035 – two at a time)
- Round bar, mild steel – ¾” (5/8” two at a time)
- Square bar, mild steel – 9/16” (1/2” two at a time)
- Maximum section modulus, mild steel – .072 (.036 two at a time)
- 1 or 2 tube at a time
- Production capacity, bends per hour approximate – 650 strokes (bends)
- Production capacity, bends per hour approximate – two at a time – 1,300
Specifications
- Maximum standard radius for 90° bend – 4.5”
- Minimum radius to diameter ratio – 2 to 3
- Maximum bend angle – 140º
- Maximum bend angel – two at a time – 100°
- Maximum bend angel with special tooling – 165°
- Bend arm repeatability – ± ¼°
- Motor horsepower – 20HP
- Approximate weight – 4,600 lbs.
- Overall height – 60 inches
- Working height to dies – 40 inches
- Footprint (floor space required) – 30 x 85 inches
- Weight – 3,100 lbs
Safety Features
- All electrical components in power panel are “finger-safe” and are in accordance with NFPA standards
- Machine is labeled with pinch and hazard points